Month: May 2021

How to bike out to the Fox River Trolley Museum

Visiting the Fox River Trolley Museum is a fun day trip for anyone who likes Chicago train history or trolleys and streetcars generally. The FRTM is free to browse, and rides cost $5 each or pay $8 for unlimited rides (adult prices).

A Chicago Aurora and Elgin interurban electric train
Decades ago, it was possible to ride this Chicago Aurora & Elgin train all the way Batavia, Illinois, from Chicago. The CA&E’s former right of way is now the Illinois Prairie Path, the first rails-to-trails project in the United States.

The museum is not accessible to people with disabilities. It’s open Sundays from May to October and some holidays (check their calendar). The museum has two portable restrooms, but I recommend using the permanent and spacious ones in County Park.

Trip option 1, the short and direct option: Take Metra’s MD-West line to National Street and bike 15 minutes south along the Fox River Trail. The trail passes County Park, where there’s a playground, restrooms, and bike parking. Lock your bike here and walk on the gravel path from the park to the outdoor museum.

Trip option 2a, the really convenient option: Have a friend who loves planning multi-modal bike trips dig into the Metra schedules and send calendar invitations to everyone in the group so there’s great expectations as to when and where the trip starts and ends. Thank you, D.S.!

Trip option 2b, the longer one that incorporates more cycling: Take Metra’s BNSF line to Aurora Transportation Center (ATC). The BNSF line has Metra’s new bike cars on specific runs (check the schedules). This is important because it means you can bike with a larger group of people than before since your group’s size is less subject to capacity constraints for bikes on standard Metra trains – without bike cars – and unpredictable directions from Metra conductors. Additionally, on standard Metra trains, the posted bike capacity may be inaccurate if the conductors have not opened all of the coaches.

This is the bike car on Metra's BNSF line, at the Aurora Transportation Center
This is the bike car on Metra’s BNSF line, at the Aurora Transportation Center.

After disembarking at the ATC, ride to the north side of the center towards the river and use the signalized intersection to cross the high-speed road to the Fox River Trail. From here on out you’ll be following the FRT northward via its off-street and on-street sections. The trail is mostly off-street, so that’s fun, and it’s nice to have so much shade.

You can basically just bike north and follow the FRT signs but you may want to review a trail map ahead of time because it’s often possible to bike on either side of the Fox River and there are advantages to riding on one side over the other in some segments. For example, from downtown Batavia north to Fabyan Villa, I prefer the west side. At Fabyan Villa you’ll have to switch to the east side.

From Aurora, look for FRT direction signs that say “Batavia”, and then “Geneva”, and then “St. Charles”, and finally “South Elgin”. I believe the only option for cycling through downtown St. Charles is on-street, and there are some hills on its FRT street sections so be prepared or look for an alternative route.

This is as good a point as any to mention that you could shorten the bike trip by taking Metra’s UP-West line to Geneva, which is north of Aurora, and heading on downhill streets to the riverfront and crossing the pedestrian bridge underneath the Metra tracks to join the Fox River Trail on the east side to head north.

My two friends and I ate at Flagship on the Fox, an American restaurant and pub with seating indoors, on a covered patio, and outdoors. The Flagship Burger, with onion rings, avocado, bacon, and white cheddar cheese was delicious. Next door is Pollyanna Brewing Company, but which doesn’t sell food.

A lot of the FRT follows the old Aurora, Elgin and Fox River electric railway line! Can you believe that there used to be interurban trains running up and down the Fox River connecting the towns there (which I mentioned above)?

The Aurora, Elgin & Fox River Electric was an interurban offering both freight and passenger service between Yorkville and Carpenter, Illinois. Operations began as early as 1895 and closely followed the Fox River for its entire route. It underwent several mergers and names over its lifetime before eventually becoming 40 miles in length and operating two streetcar services in Aurora and Elgin.

As with most interurbans, the AE&FR was overtaken by buses and the automobile, and passenger service was discontinued in 1935. Freight service continued along portions of the route up until 1972.

AbandonedRails.com

The AE&FR ran on the Fox River’s west bank from Aurora to St. Charles, where it switched to the east bank. On approach to South Elgin, however, and due to a big bend in the Fox River, it kept going straight and found itself on the west bank again.

A bend in the Fox River moves the AE&FR interurban line from the east bank to the west bank again.
The former AE&FR bridge crossing the bend in the Fox River is now part of the Fox River Trail. Photo: Eric Allix Rogers

A minute or two after crossing the bend in the Fox River on the former interurban’s bridge, you’ll encounter the southern end of the Fox River Trolley Museum’s demonstration track. Less than 10 minutes later and you’ll be arriving at County Park where I recommend parking your bike.

What’s the timing on this? I don’t know. My friends and I took our time cycling and stopping for photos and eating. The relaxed riding nearly prevented us from being able to ride a trolley. The museum runs a trolley once an hour every hour, and we arrived a few minutes after the most recent trolley left the station. We needed to be in Elgin to ride Metra’s MD-West line back to Chicago at 15:55, and the next full ride would take so long that we would miss that train, and since it’s Sunday, it’s safe to assume that the next Metra train runs two hours later.

The volunteer staff at the museum were sympathetic to our case and created a special charter for just the three of us! The two operators and an apprentice took us on a shortened journey down the line, from Castlemuir (the home station) to a switching yard of sorts halfway down the line. The yard is where trains could be rerouted to a track that joined up with former Illinois Central tracks going east-west.

Our motley crew. Eric captioned this, “NBD just a private excursion along the Fox River in an old North Shore Line car!” Photo taken by one of the qualified train operators.

We rode the former North Shore Line car 715. This car used to run between Chicago and several cities along the North Shore, including Evanston and Willmette (where the Chicago Transit Authority’s Purple Line runs now), Skokie (where the CTA’s Yellow Line runs), and further north to Milwaukee. Check out the North Shore Line’s route map on the Northwestern University Transportation Library’s website.

Former North Shore Line car 715 at the Fox River Trolley Museum

You would have also seen car 715 running around the Chicago elevated loop, and making stops at the existing Belmont and Wilson elevated stations (although both of those have been replaced and tracks re-aligned for slightly faster service).

Once you’re done enjoying the historic trains at the FRTM, get back on the Metra and go home. Check out Elgin’s riverfront if you have to wait, and there are restaurants in downtown Elgin.

Elgin, Illinois, riverfront

Two-flat journal 6: How to make an all-electric house

After the bill drama with Peoples Gas last year, in which I was billed a $50 “base” fee per unit per month for the privilege of having a gas line to my house, I decided to make the gut rehab of my two flat all electric. I think that making an all electric house is easy, but it takes a lot of research to know what that means and how to select materials and appliances.

Read all of the “Two-flat owner journal” entries

Why go electric?

I have several reasons for keeping natural gas out of my house:

  • Natural gas has point source emissions causing indoor air pollution that need to be vented and evacuated properly (gas stovetops emit methane into your kitchen, so turn on your hood that hopefully vents to the outside)
  • The price of natural gas is not falling as fast as electricity is falling
  • Electricity is more and more likely to come from renewable sources, especially in Illinois because of our state policies that require ComEd and Ameren to buy more and more power from renewable sources
  • A future photovoltaic solar panel array could be integrated and some of the electricity in the house would come from its own generator
  • Without gas pipes in the house, there is less infrastructure to build and maintain
  • Climate change is continuing to make life harder for the world’s inhabitants and electrical heating & cooling causes less fossil fuel emissions (“An electrified home uses 8,333 more kWh annually than a gas (or propane) home but displaces 96 million BTU of fossil fuel use.”Elevate+Rocky Mountain Institute study)

There are still some downsides to having an all electric house, namely when the power goes out on the block then nothing in the house will turn on. There are solutions, for this, though, including integrating a battery pack or using a fossil fuel-powered generator with its own tank.

The Passivhaus-certified single-family house in Hyde Park that I toured in 2018 has a small natural gas-powered generator in the rear yard, fueled by a typical Peoples Gas supply line.

What does it mean to have an electric house?

I think there are three categories of choices that one makes, about visible appliances, invisible appliances, and heating & cooling.

A visible appliance is one you use directly and frequently, like an oven and a clothes dryer. These are essentially the only two appliances that have gas and electric versions and electric versions are just as commonly available as gas version.

An invisible appliance is one that’s in a closet or in the basement, like a water heater. Most people I know have a gas-powered water heater (usually a tank, not tankless), and there are two kinds of electric water heaters (which I detailed in Two-flat journal 3). Again, these are very common and electric water heaters (standard with resistance heating, tankless, and hybrid heat pump) can be picked up anywhere a gas-powered water heat can be purchased.

Think of a heat pump as a “reversible air conditioner”: an air conditioner removes heat in the air of a space and puts it outside, while a heat pump “removes” the heat in the air of the outside and puts it inside.

Heating & cooling is the complicated category of the three. A typical new construction house or condo has gas forced air for heating, a condenser for air conditioning, and the air is pushed through the house via ducts. In the electric universe, however, mini splits/air source heat pumps have been around for 40 years and are extremely efficient at both heating and cooling. In cold climate region 5, where Chicago is, air source heat pump manufacturers have additional products to deal with the extreme cold temperatures.

Going electric in the heating and cooling category is the only one that necessitates deeper research on windows, wall assembly, and insulation to go beyond the basic energy efficiency code (Illinois Energy Conservation Code 2018). While the air source heat pump is efficient (some have a coefficient of performance, COP, of 3-4, meaning it transfers three to four times as much heat energy to the house as the energy they consume) it will work very hard to keep a house warm during negative temperature days (F°) and thus it’s important to have a well-sealed house so the conditioned air you’re paying for doesn’t escape.

If you want your house to be all electric, a lot of these choices can be made over time. For example, you can stop the air pollution by buying a range with an induction cooktop, which is extremely efficient, safe for households with children, and very easy to clean. I like to cook soup in my Dutch oven (which is compatible with induction cooktop) and I would rather not have to have the burner on for an hour, accompanied by a noisy vent fan.

Financial benefits of an all electric house

In addition to certain federal tax credits for replacing certain appliances, which you can claim when you file your tax return, there are often local incentives. ComEd has a new Electric Homes program that offers $4,000 cash (to the builder or general contractor) for an electric house (new construction or renovation) that meets their requirements. (2021 is the second year in operation, and there’s no guarantee it will operate next year.)

From ComEd’s marketing:

Building your clients’ dream homes – why not make them energy efficient?

ComEd provides a $2,000 incentive per home for electric homes new construction! All-electric home construction can sound daunting at first, but with the knowledge and help of ComEd, you too can benefit from tight envelope, all-electric HVAC, heat pump water heating, lighting and appliances. Construction of single-family homes, duplexes, townhomes, and 2-4 flats are eligible.

Make the jump to high-quality, next-generation, electric homes. Reduce energy bills while providing superior comfort. Prepare for a clean, resilient energy future.

Learn about additional clean energy strategies like solar power, electric vehicle charging, smart homes and induction cooking.

Please reach out to Sophia Seol SSeol@slipstreaminc.org if you have any questions.

I’m planning to buy these products

I’ve done a lot of research on appliances in all three categories because my architect needs to know exactly which appliances I’m selecting so the kitchen, utility closet, basement, and other spaces can be designed to fit them. Thankfully, a lot of appliances have similar dimensions so it’s easy to match the available space with the catalog of laundry machines, refrigerators, etc.

My architect and I reviewed a printed set of plans last week, mainly so he could alternate between drawing on AutoCAD and marking up issues.

There are two main attributes to watch for when selecting electric appliances: the yellow Energy Guide label that estimates the annual cost of operating the appliance, and whether it has Energy Star certification. One of the ComEd Electric Homes requirement is that every appliance that can be Energy Star certified is – I’ve found that there are no certified ranges.

My favorite place to shop for appliances online is Abt. When I polled my Twitter followers last summer for appliance store recommendations, Abt was overwhelmingly the most recommended store.

Note: I have no idea which ones will be in stock when it comes time for me to buy any of them, but these are the ones I would pick right now.

All appliances and equipment are Energy Star-certified except where noted.

Visible appliances

  • Dishwasher. I’ve got three options on my list (each costs less than $500):
  • Refrigerator (a different one for each dwelling unit)
  • Oven/stovetop/range
    • Frigidaire FCRE3052AB ($629) – Not Energy Star certified, not induction
    • Frigidaire GCRI3058SS ($1,169) – Not Energy Star certified, yes induction

Invisible appliances

  • Water heater. Something to know about tankless is that it’s not necessary to have a single tankless source for the whole house, as it’s possible to have multiple tankless water heaters at each water source, sized to the need – the kitchen sink can have one, and the shower and the lavatory can share another. The hybrid heat pump water heater currently has a 10% federal tax credit, up to $300.
    • Rheem brand’s “Performance Platinum 40 Gal. 10-Year Hybrid High Efficiency Smart Tank Electric Water Heater” (Home Depot)
    • Each dwelling unit will have the same water heater but may not have the same kitchen and laundry appliances.
  • Clothes washer. Stacked, to save space, from (each is about $800):
  • Clothes dryer. Stacked, to save space, from (each is about $800):

Heating and cooling (HVAC)

Mini split systems have two parts: An outdoor condensing unit and one or more indoor fan units. They’re connected by a refrigerant line, an outgoing condensation line, and electricity from the outdoor unit to the indoor units that is routed through a small diameter (3″) hole in the exterior wall.

Three outdoor heat pumps on the roof
Three larger-capacity heat pumps on the roof of a new construction and all-electric three-flat in Pilsen. Photo: Steven Vance.

There are several options for indoor units: Wall-mounted, ceiling mounted cassette, ceiling mounted box, and ducted (the outdoor unit will provide the hot or cold refrigerant and the ducted unit will blow air through a duct network). My architect and I have selected two ceiling-mounted cassettes per dwelling unit; these fit within the 16″ between joists and avoids the protrusion of wall-mounted units.

  • Outdoor unit, Mitsubishi MXZ-3C30NAHZ2 (Ecomfort, $3,365 x2)
  • Ceiling cassette indoor unit, Mitsubishi MLZ-KP09NA (Ecomfort, $895 x4)

I will need a venting system to exchange fresh air into each dwelling unit, without relying on the typical situation where the leakiness of houses brings in fresh air. An energy efficient way to do this is to use an “energy recovery ventilator” (ERV) that transfers the heat or chill of outgoing conditioned air to incoming fresh air to reduce the amount of energy that the heat pump would expend to warm or chill the incoming air.

An alternative to ducted ERVs is to use a wall-mounted model, such as the Zehnder ComfoAir 70 ventilation unit, Holtop ERVQ-B150-1A1F, or Blauberg VENTO Expert A50-1 W (that’s on Blauberg’s German-market website, and that company has a subsidiary called VENTS that has an American-market website). There’s also Panasonic’s WhisperComfort ($420) that can be mounted on the wall or ceiling. However, I need to verify that either has air moving capacity required by the indoor air quality standard ASHRAE 62.2, specified in the ComEd Electric Homes program. It might be possible to use two of these, including one in the bathroom.

What’s missing

Oh, one more thing, the electrical panels in the basement will need to be replaced (which is part of the replacement of the entire electrical system), and ComEd will likely need to string higher-amperage lines from the alley overhead power lines to the house. This area requires more research and possible a conversation with an electrical contractor or ComEd. I’m currently assuming that I can specify that the electrical contractor will handle this with ComEd.